Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Dvele Fence Installation: The Los Angeles Owner’s Guide
Dvele fence installation in Los Angeles typically runs $4,130 to $10,620 installed, depending on linear footage, terrain, and whether we’re replacing a failed section or setting an entirely new run. That’s the honest range we quote most homeowners in Los Angeles, and it includes tear-out, post setting, panel or slat installation, and haul-away. Most Dvele owners discover a fence problem the same way: a gate sags, a post leans after rain, or a panel cracks at the fastener line. You’ll get a written price before we touch the first post hole, and the technician’s name and photo before they arrive.
Which Dvele Models This Applies To
Dvele homes built across Los Angeles use consistent exterior fencing specifications, but there’s a compatibility gotcha every owner should know. Dvele typically specs horizontal slat fencing with concealed fasteners, and the spacing between slats varies by elevation and fire zone requirements. In Los Angeles hillside areas like Mount Washington and Baldwin Hills, we see tighter slat spacing and non-combustible posts more often than in flatland neighborhoods. Before quoting, we match the existing post spacing, slat width, and fastener pattern to the original install. If you can find the original build sheet or the fencing submittal from your closing documents, that speeds things up, but we can also pull measurements on site. For Dvele fencing specifically, we recommend OEM-matched materials over generic big-box equivalents. The slat profile and the powder-coat finish have to match the rest of the home’s exterior, or the repair stands out like a patch job. Mason Remodeling is an independent service provider, not affiliated with Dvele, but we’ve installed and repaired their fencing specs across Los Angeles enough to know what works and what doesn’t.
Styles & brands we work with
Signs Your Dvele Fence Installation Is Failing
- Gates that drag or won’t latch. This usually means the post has shifted out of plumb, either from soil movement or a footing that was undersized for Los Angeles’s expansive clay in neighborhoods like Sherman Oaks and Encino. A sagging gate is a symptom, not the problem itself.
- Leaning posts after winter rain. Los Angeles gets intense wet-dry cycles, and shallow post footings heave. We see this most in hillside areas where runoff collects along the fence line. The post may look fine, but the footing has failed.
- Rust bleed at fastener points. On powder-coated steel or aluminum fencing, you’ll see orange or white corrosion weeping from screw holes. That means the factory coating was compromised during installation or by impact, and the metal underneath is oxidizing. In coastal Los Angeles neighborhoods like Playa del Rey, salt air accelerates this dramatically.
- Warped or cupped slats. Horizontal slat fences fail when slats were cut too tight between posts, leaving no room for thermal expansion. Los Angeles heat, especially in the Valley, turns a tight cut into a bowed slat within two or three summers.
- Loose or missing concealed fasteners. Dvele’s concealed fastener system is clean, but it’s unforgiving. If a fastener backs out, the slat it held loses structural connection and starts vibrating in wind. You’ll hear it before you see it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Los Angeles Dvele fence work, you’re looking at $4,130 to $10,620 for most full replacements or substantial section repairs. A simple gate post reset with new hardware might fall toward the low end. A full perimeter replacement with steep terrain access, non-combustible materials, and a long run pushes toward the top. Here’s how that range breaks down:
- Post replacement with concrete footing: $180 to $340 per post, including excavation and haul-away.
- Slat or panel replacement: $38 to $85 per linear foot, materials and labor together.
- Gate rebuild or rehang: $470 to $1,180 per gate, depending on width and hardware.
- Full fence removal and disposal: $590 to $1,420 for a typical Los Angeles lot.
- Terrain or access surcharge: $290 to $710 when posts must go into hill slopes or you’re working behind a retaining wall.
Every job includes a written line-item price before work starts, and the work is covered by our 365-Day Done Right Promise. If the fence isn’t right within a year of completion, we make it right at no cost to you. No surprise invoices. No verbal estimate that grows on the final bill.
DIY or Call Us?
You can safely check for obvious cause: walk the fence line, look for leaning posts, rust bleed at fasteners, and slats pulling away from the rails. That’s useful information when you call. What we don’t recommend is pulling a post and re-setting it yourself. Dvele fencing posts are load-bearing; if the footing is undersized or the post isn’t set in the right concrete depth for Los Angeles soil, the repair lasts a season and then fails again. Setting posts requires knowing the local frost depth isn’t the issue here, it’s the shrink-swell clay in places like Atwater Village and Highland Park, and it’s the wind load on long horizontal runs. The material cost to fix a post you re-set wrong once is often more than the labor would have been to do it right the first time. Call (803) 680-2547 and we’ll walk the line with you, tell you what’s failing, and put the price in writing before we start.
FAQs
A properly installed Dvele-spec fence in Los Angeles should last 15 to 25 years, with powder-coated aluminum or steel posts lasting longest and wood or composite slats needing attention sooner. Coastal air in neighborhoods like Venice and Mar Vista shortens unpainted metal life by several years. The single biggest lifespan factor is post footing depth and drainage. Call (803) 680-2547 for an exact quote on your fence line, estimates are free.
A leaning post can usually be re-set if the post itself isn’t rusted through or cracked. We excavate the old footing, inspect the post base, and re-set in fresh concrete with proper drainage. If the post shows interior corrosion or stress cracking, replacement is the honest fix. We’ll tell you which one you need before we do the work, and the price won’t change once we start.
A single post reset is typically a half-day job. A full fence replacement on a standard Los Angeles lot takes two to three days. Terrain, access, and materials availability can push that to four days, and we’ll tell you the schedule before we start. Call us at (803) 680-2547 and we’ll give you a written timeline with your written price.
We stock common Dvele-compatible fence hardware, concealed fasteners, and post materials on our trucks, along with parts for KraftMaid, Cambria, and Silestone on the cabinetry and surface side. For full slat runs or custom powder-coated panels, we order exact-match materials and schedule the install when they’re in hand. You’ll know what’s in stock and what’s on order before we start.
Written by Isaac Pruett, Owner, Mason Remodeling at Mason Remodeling, serving Los Angeles and nearby areas.
