Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Construction in Fresno, CA | Mason Remodeling
Mason Remodeling provides independent CGI cabinet installation, repair, and refacing across Fresno, CA. We’re not a dealer or authorized service center, which means we troubleshoot the actual failure in your kitchen instead of steering you toward a brand line. If your CGI thermofoil doors are peeling off Champlain Drive or your sink base has swollen near Fresno State, call (803) 680-2547 for a free estimate.
Why Fresno Homeowners Call Us for CGI Cabinet Work
CGI cabinets show up in a lot of Central Valley kitchens because they’re affordable and easy to order. The catch is that Fresno’s climate punishes RTA construction harder than most places in California. Our crew has been pulling failed CGI boxes out of homes in Sunnyside, Tower District, and Woodward Park for years, so we know exactly what to look for before we open a single tool bag.
Isaac Pruett learned finish work from his dad, a finish carpenter, and it shows in how we handle cabinet edges. The first thing he checks on every job is the trim and door alignment, because sloppy work there means the whole kitchen looks wrong. We bring that same standard to every CGI repair in Fresno, whether it’s a single delaminated door or a full run of uppers.
We’re an independent shop, not factory-affiliated. That matters when a homeowner needs an honest answer about whether to repair or replace. We’ll tell you if your boxes are worth saving.
Styles & brands we work with
Common CGI Cabinet Problems in Fresno
Here’s what we see again and again in Fresno homes, tied to the specific conditions that cause them:
- Thermofoil peeling on door edges. Fresno summer temperatures climb well past 100°F, and the air in an attic can hit 140°F or more. Cabinet uppers near the ceiling sit in that heat every afternoon. Thermofoil adhesives rated for far cooler conditions let go, and you’ll see it first on edges facing the range or a west window.
- Swollen particleboard sink bases. A slow plumbing weep under the sink or slab moisture wicking up through the floor on an older raised foundation is all it takes. Once the core swells, the box loses its structure. We see this in pre-1980 Fresno homes about as often as not.
- Stripped hinges and loose drawer slides. CGI RTA hardware works fine on a flat, square wall. Fresno homes settle, floors shift, and a cabinet run racked a quarter inch out of square eventually strips the adjustable hinge screw holes, so doors sag and drawers bind.
- Sun fading on south- and west-facing cabinet faces. Single-pane or older dual-pane windows in Fresno give UV a direct path to the finish. A kitchen with a big west window in the Fig Garden area will bleach one run of doors noticeably faster than the others.
- Doors out of alignment after humidity swings. Winter fog season brings damp air, then the heater dries the house out. That cycle makes MDF and particleboard move enough to torque door and drawer fronts out of plane. It’s slow, but over three or four seasons it shows.
CGI Service in Fresno: What the Local Climate Does to Your Cabinets
Fresno experiences summer design temperatures that push attic and cabinet-line air far above what many RTA cabinet adhesives are rated for. A thermofoil door isn’t stressed at the factory in a climate-controlled warehouse; it’s stressed in a Clovis-adjacent kitchen with a west-facing window in July. Then the Tule fog rolls in from December through February, raising indoor humidity, and the heater pulls all that moisture out of the air over and over. The combination is brutal on any engineered-wood cabinet, but it hits RTA lines hardest because the skins and cores aren’t built for that cycle. This is why we see failures at edges and skins first, not in the middle of the panel.
On a job off Champlain Drive in northeast Fresno, we pulled a run of CGI RTA thermofoil uppers that had exactly this pattern: peeling door skins, a swollen sink base from an old slow leak. We salvaged the sound boxes, reattached new doors with Blum-style slides, replaced the swollen base, and set a quartz top over the run. The homeowner kept their layout and got a kitchen that actually holds up to Fresno heat without tearing everything down. That’s the repair-first judgment call that only comes from seeing enough failures to know what’s worth saving.
CGI Models & Products We Service in Fresno
We work on the CGI Ready-to-Assemble shaker and flat-panel lines sold through the big-box stores and online channels, plus the semi-custom framed and frameless series in painted and thermofoil finishes, and CGI vanity and Fresno Bathroom Remodeling cabinetry configurations. For any repair we use OEM-matched hinges, slides, and touch-up finishes when they’re still available for your cabinet run. When a factory part is discontinued or stuck on national backorder, we’ll switch to quality aftermarket hardware that fits the existing bore pattern and carries the same load rating. We keep common hinge, slide, and touch-up stock on hand for faster turnaround all over Fresno.
See the difference
Before
After
Before
After
Before
AfterCGI Cabinet Service Pricing in Fresno
Here’s the honest price picture for CGI cabinet work in the Fresno market. Refacing usually lands lower than replacement, but if your cores are swollen or the finish has failed across an entire run, new boxes are the smarter spend.
| Service | Typical Range in Fresno |
|---|---|
| Cabinet Installation | $4,000 – $13,000 |
| Countertop Installation | $2,000 – $6,500 |
| Backsplash Installation | $800 – $2,500 |
| Kitchen Remodel | $14,000 – $45,000 |
| Small Kitchen Remodel | $9,000 – $20,000 |
| Bathroom Vanity Installation | $800 – $3,000 |
What drives the price is the condition of the boxes, whether you’re refacing or replacing, and the countertop material you choose. A free estimate covers all of it. Call (803) 680-2547 and we’ll walk the job with you, no obligation.
Serving Fresno, CA - Our Local Coverage Area
We’re a General Contractor in Fresno and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About CGI Construction in Fresno
CGI is a cabinet brand. They manufacture ready-to-assemble and semi-custom cabinet lines, including shaker and flat-panel doors, vanity configurations, and bath cabinetry. Countertops are typically sourced separately. Call (803) 680-2547 and we’ll help you sort out what you’re working with.
Fresno’s summer heat pushes attic and cabinet-line temperatures above what many RTA thermofoil adhesives can handle, and winter fog adds humidity swings that stress the bond. The finish fails at the edges first, especially near ovens and west-facing windows. A repair usually means re-skinning or replacing the doors, not the whole cabinet run.
Yes, in most cases. We match the door profile, finish, and hardware to the existing run, using OEM doors when available and quality comparable doors when the original line is discontinued. Matching a paint finish exactly is the hardest part, so we’ll bring samples to the site before you commit. Call (803) 680-2547 to set up a look at the damage.
Yes. A sound CGI cabinet frame supports a quartz or granite top just fine. The catch is the boxes must be solid, square, and properly shimmed first. We check the runs before any stone goes on. If the cores are swollen or the frame is racked, we’ll tell you before we’re mid-install.
No. Mason Remodeling is an independent service provider, not a CGI dealer or factory-authorized shop. That independence means we recommend the repair that makes sense for your kitchen, not the one that moves product for a brand. For an exact quote on your CGI cabinets in Fresno, call (803) 680-2547.
Service Areas Near Fresno
We cover all of Fresno proper, from Woodward Park down through Tower District to Sunnyside, and we take jobs in nearby cities and neighborhoods around the Central Valley. If you’re within driving distance of a Fresno address, we’ll likely come to you. Compare our work with CGI service in Sacramento or see how our approach differs from CGI service in Miami. For a wider look at coverage, visit our Fresno service area page, and for more about how we handle CGI repairs and installs, see CGI sales & service.
Book Your CGI Cabinet Service in Fresno Today
If your CGI doors are peeling, your drawers are binding, or your sink base is swollen, don’t wait until the damage spreads. Call (803) 680-2547 now and we’ll set up a free estimate. A live person answers, day or night, even on weekends.
Written by Isaac Pruett, Owner at Mason Remodeling, serving Fresno since 2004.
